• German - Version
  • English - Version
  • Czech - Version
  • Romanian - Version
  • Hungarian - Version
  • Slovakian - Version
  • Filter

     

     

  • Kabelbearbeitung

  • EMV

  • Verbindungstechnik

  • Kabelbearbeitung

  • Crimptechnik

  • Prüftechnik

  • Schrumpfen

  • Kabelbearbeitung

  • Wickeltechnik

Fully automatic cable harness production

 

 

Zeta 640 / 650

Fully automatic cable assembly machine

Different cables and contacts are processed automatically without having to change over. This makes batch size 1 possible without any special effort. The manufacturing time is reduced by up to 50 % compared to traditional manual methods. A consistent data flow from the planning software to production reduces errors and increases cost-effectiveness.

At the end you get the cables you require in the correct order with the desired marking, and bundled ready for further processing.

 

Technical data


Zeta 640Zeta 650
Number of stations / with expansion5 / 108 / 13
Number of cables36
Process modulesCrimping, fitting seals, twisting, tinning, sleeve loading, double gripper, ferrules, MIL crimping, welding, ultrasonic compaction
Quality assuranceIntegrated crimp height and pull-out force measurement, crimp force monitoring, splice detection, incision monitoring, material change detection and material verification, Seal position monitoring, contact end detection

Zeta 630

Harness Manufacturing Zeta

The Zeta 630 makes switchboard construction efficient and just in time. Thanks to the economical automation process, cable assembly is highly productive, starting with batch size 1. Automated processes and lot or sequential production without retooling shorten production times by up to 50 percent. The automatic wire changer provides up to 36 different lines, and the CM 1/5 GS module processes up to five different wire end ferrules. The reliable, fully automated production ensures consistent high quality.

 

Technical data

Line cross-sections0.22–6 mm² (AWG 24–AWG 10)
Wire changermax. 36 wires (in steps of 6 wires)
Lengths with double-sided processing240–3,000 mm standard trough;
240–5,000 mm optional
Lengths with one-sided processing85–3,000 mm standard trough;
85–5,000 mm optional
Number of stations2

DLW – Digital Lean Wiring

Software for switch cabinet construction

With an efficient data processing, the DLW (digital lean wiring) software from Komax provides automation in switch cabinet construction. This means that a significant amount of time is saved in comparison to manual manufacturing, even with a batch size of 1.

Compared to conventional ECAD systems, the usage does not cause any cost-intensive maintenance of the components since the cable length can be determined by virtual wiring. It can be done by means of a photograph of the cabinet or a 2-D drawing. Existing data can easily be imported. Alternatively, Komax offers a camera for photographic dimensioning with a round shot in several individual images. The images are then put together into a dimensionally accurate overall picture and imported into the DLW.

The DLW also features an easy-to-handle user interface with touch screen. The DLW Viewer guides the operating staff through the entire wiring path, allowing even less specialized personnel to perform this step.

Omega 740 / 750

Fully automatic cable harness manufacturing machine

The Omega 740 and 750 are used for the fully automatic production of cable harnesses that are fitted from both sides. Up to 36 different cable types can be processed at the same time. With up to eight processing stations, almost all manufacturing processes can be reproduced and cable assemblies can be made efficiently without change overs. Marking is automated, using two ink-jet printers. The Omega passes the cables to a connected block loader fully automatically.  With many improvements such as optical monitoring, a larger carrier plate and much more, it can now even fit the smallest connector housings or other components, fault-free.

 

Technical data


Omega 740Omega 750
Number of stations / with expansion5 / 108 / 13
Number of cables36
Process modulesCrimping, fitting seals, MIL crimping, ferrules, ultrasonic compaction
Quality assuranceIntegrated crimp height and pull-out force measurement, crimp force monitoring, splice detection, incision monitoring, material change detection and material verification,
Assembly: Collision, insertion force and contact locking Monitoring

Wire-XL / Wire-XXL

Multi Connection Machine

The Wire-XL / Wire-XXL can be equipped with a wide variety of modules for the following processes: Stripping multi-conductor cable, shrinking of contacts and sensors, compacting, welding, fluxing-soldering, splicing, housing insertion, etc. Various modules are also available for quality control, such as crimpheight measurement, colour detection, crimpforce monitoring, pullforce measurement, camera, insertion force, insertion depth, etc. It’s designed for high volumes in the automotive, industrial and aerospace sectors.

MES – manufacturing execution system

Software solution for the cable processing industry 4.0

The production software jointly developed by Komax and iTAC has been perfectly custom-tailored to the needs of cable manufacturing. The end-to-end solution has been designed for the entire value chain – from goods receipt through all production steps all the way to goods issuing – of cable processing companies of any size.

The software can be used for automated planning, control and monitoring of the entire production: machines, manual workplaces, auxiliary materials, material flow, resources, etc. Processes can be optimally standardized, defective production can be prevented, and the product quality can be significantly boosted. This makes it possible to produce complex products in the desired quality on schedule.

Anrufen E-Mail Top
Schließen

Callback Service

Callback Service
We would be happy to call you back for a consultation!