Mixing and dosing system and overall dosing systems: THONAUER GmbH

2-K-DOS

Mixing and dispensing system

This mixing and dispensing system delivers 2-component material and adhesives based on polyurethane, epoxy and silicone quickly and accurately.

Technical data

Mixing range	1:1 to 1:10
Flow rate	20–1,000 g/min
Mixing system	static

HOBBO-DOS

Hobbok dosing system

HOBBO-DOS is a device with which the two components A and B from the two containers on the ground below – HOBBOK – are directly conveyed into the 2-K-DOS mixing and dosing device.

Technical data

Flow rate	max. 1,000 ml/min depending on the potting compound
Viscosity	max. 40,000 mPas

ROBO-DOS

3-axis working table

The ROBO-DOS in combination with the mixing and dosing system 2-K-DOS forms a robot system for fully automatic dispensing and application of electronic assemblies, sensors, seal tracks, etc.

Technical data

Work area	from 40 x 30 to 100 x 60 cm
Max. speed	50 mm/sec.

LIN-DOS S

Linear unit

LIN-DOS is a three axis linear unit for the automatic sealing of rails, in particular LED strip light, in combination with the mixing and dispensing units 2-K-DOS or 2 K MiniDOS.

Technical data

Work area	X: 6 m max.; Y: 50 cm max.; Z: 110 mm
Transportation speed	0.1–100 mm/sec.

DC-CNC 250

Workbench dosing cell

Compact design and yet flexible
High-precision dispensing of small volumes, from 5 mg/dosing point
Processing of highly abrasive 2K materials

Technical data

Flow rate, mixing ratio	0.02–0.5 cm³/sec @ mixratio 1:1
Mixing ratio	up to 1:100
Shot size	min 0.005 cm³, max. 5 cm³
Material supply	20-oz.cartridges (600 ml)

DC-CNC 800

Dispensing cell

Compact and flexible - the new dispensing system for dynamic sealing, bonding and encapsulating. Features: 2K-material conditioning on carriage for easy maintenance; servo-driven high-precision gear pumps; integration into existing production lines possible, etc.

Technical Data

Flow rate, mixing ratio, viscosity	Depends on installed mixing system
Max. travel speed	X, Y = 60 m/min., Z = 40 m/min.
Work area	X, Y, Z = 800, 400, 200 mm

DR-CNC

Dispensing robot

Variable X-Y-Z strokes enable the three-dimensional dispensing of sealants, adhesives, and encapsulates. The DR-CNC is equipped with the highest standards in CNC technology to combine the mixing and dispensing system with maintenance-free CNC linear axis.

Technical Data

Flow rate, mixing ratio, viscosity	Depends on installed mixing system
Max. travel speed	X, Y = 60 m min-¹; Z = 24 m min-¹

C-DS

Compact dispensing system

The C-DS dispensing system is highly versatile and can be used as a manually operated unit, an automated partial solution, or a fully automated robot system. The system consists of a material conditioning, metering, and mixing unit, and PLC controls. The modular design simplifies integration into existing production lines.

Technical Data

Flow rate, mixing ratio, viscosity	Depends on installed mixing system
No. of material components	1–4

MK and MS

Mixing systems

Mixing systems, as diverse as your applications. A solution for every task: selection of the mixing system is according to material and application.

Technical Data

	MK 0108	MK 200	MS-SC
Dosing range	0,01–1 g sec-¹	5–200 g sec-¹	0.05–5 g sec-¹
Mixing ratio	5:100–100:100	1:100–100:100	10:100–100:100
Mixing system	Dynamic	Dynamic	Static

2-component mixing and dispensing systems

2-K-DOS

HOBBO-DOS

ROBO-DOS

LIN-DOS S

DC-CNC 250

DC-CNC 800

DR-CNC

C-DS

MK and MS

Callback Service